![new macbook pro keyboard space bar new macbook pro keyboard space bar](https://i.ytimg.com/vi/fM5PO55aRTY/mqdefault.jpg)
![new macbook pro keyboard space bar new macbook pro keyboard space bar](https://i.ebayimg.com/images/g/9GcAAOSwgYlco34Z/s-l1600.jpg)
If that doesn't help, you are "stuck" with two choices - replacing the whole topcase and keyboard, or replacing the keyboard itself, which is more difficult. If the key is installed correctly, the opposite corner should respond at the same level (not tilted higher or lower).Hi! I don't know what approach you took while cleaning the keyboard, but I would literally pull the spacebar off the keyboard (you can snap it back on afterward), and thoroughly clean everything under the key with 90% rubbing alcohol and a q-tip, as well as the underside of the key itself, and see if that loosens it up to the point where it's not sticking. Check the key from all angles to make sure it is uniformly flat. Press the length of the Space bar to ensure all clips are secure.ġ5. (Listen for the keycap clicking into place.)ġ4. Press along the top of the Space bar to secure it to the top stabilizer bar. (The keycap is tilted up at this stage.)ġ3. Press and slide your finger along the bottom of the Space bar over the bottom stabilizer bar until you hear the clips click into place. Align the bottom row of clips inside the bottom edge of the keycap with the bottom stabilizer bar.ġ2. These top clips most closely match the longest stabilizer bar at the top of the keycap well.ġ1. The top of the keycap has the row of clips that extend closest to the sides of the keycap. Determine which is the top of the Space bar keycap by checking the clips on the inner plane. If the bottom stabilizer bar is pushed up, move it down as far as it will go.ġ0. Check the keycap well area on the top case. With the scissor pins inserted, use a black stick to raise and lower the scissor mechanism to make sure it moves freely.ĩ. Allow the scissor mechanism to fold flat and hold the slider bar in place while using a black stick to insert the scissor pins-one at a time-into the top case ears.Ĩ.
#NEW MACBOOK PRO KEYBOARD SPACE BAR INSTALL#
With the scissor mechanism open, install the slider bar under the metal hook of the top case.ħ. If a metal stabilizer bar is bent, try to straighten it.Ħ.If either or both are broken beyond repair, replace the top case. If the two metal ears are bent, use needlenose pliers to straighten them.If it is bent or broken beyond repair, replace the top case. If the metal hook that holds the slider bar of the scissor mechanism is bent, try to bend it back to a uniform 90-degree angle.If the rubber dome is off center or damaged, replace the top case. When the rubber dome is pressed and released, it should spring back upright.Check the rubber dome and raised metal areas inside the keycap opening on the top case. If the clips are intact, re-use the keycap.ĥ.If any of the clips are bent, broken, or missing, replace the keycap.Inspect the rows of clips on the underside of the keycap. The slider bar and all four pins should be intact.Ĥ.When closed, its profile should be fully flat.The inner piece should pivot smoothly within the outer piece.If it is loose, remove it and compare the two parts of the scissor mechanism to the image below.If it is installed correctly, the scissor should move smoothly.Test the operation of the scissor mechanism by using a black stick to carefully raise and lower the mechanism.
![new macbook pro keyboard space bar new macbook pro keyboard space bar](https://www.ubuy.com.tr/productimg/?image=aHR0cHM6Ly9tLm1lZGlhLWFtYXpvbi5jb20vaW1hZ2VzL0kvNDFUN0tuV0dENUwuX0FDX1NMMTAwMF8uanBn.jpg)
Lift away any built-up adhesive using fine-point tweezers.ģ. Because adhesive is used under the top case, closely inspect the case for any adhesive that may have built up under the keycap.
![new macbook pro keyboard space bar new macbook pro keyboard space bar](https://www.lifewire.com/thmb/gUzk-Thhk7MgKft3xQUVYO5_haw=/1560x1042/filters:no_upscale():max_bytes(150000):strip_icc()/how-to-clean-your-mac-macbook-macbook-pro-keyboard-4586910-1-5c5f595846e0fb00015875cb.jpg)
If a rectangular-shaped key needs to be removed (for example, if a key is sticking when pressed), always pry it up from the left side-either the upper or lower left corner.Ģ.